Delorean Parts
|
|
|
|
|
Major
Delorean Tune up
& service kit with all new
parts no old or NOS.
Includes
Oil Filter, 02 Sensor
VC Gaskets Left & Right
Fuel Screen for tank & Fuel filter,
Plug
Wires, Cap, Rotor, Spark Plugs.
AC Belt and Alternator belt.
Air Filter, oil pan gasket for MT.
$189.95
Add to Basket
With automatic trans filter kit.
$274.95
Add to Basket
|
Delorean High Performance
service & tune up kit.
You will feel the difference.
Everything you see for:
$259.95
Add
to basket
If bought separate would be
$277.55
Save 10%.
8mm HP wires low resistance.
Bosch Platinum +4 plugs
Pertronix 40,000 volt coil.
K&N HP low resistance filter.
+ more as you see.
|
Our most popular Performance tune-up kit.
Platinum +4 plugs &
8mm Taylor
silicone performance wires with life
warranty against any electrical breakdown.
Add to Basket
$144.95
Includes everything you see.
|
Were are now carrying
Champion Spark
Plugs.
For the De Lorean.
Champion copper tip plug
$1.49 ea.
Add to Basket
|
DeLorean Hervey headers in
Stainless Steel.
These headers are professionally welded in the same style as
other performance
and NASCAR headers and fit the Delorean exhaust system
without having to
remove the starter. They come in bead blasted and we also offer them in polished
or ceramic plated . We also have the stainless starter shields.
$895.00 Add to Basket
|
DeLorean Exhaust Magnaflow Turbo Stainless
Steel mufflers that can be used with the headers.
|
|
Delorean Hervey
header
Ceramic plated.
Extra thick flange plate
$695.95 Pr.
Add to Basket
Header Catalytic converter.
Highest quality in
a
small size. |
Stainless heat shield
built in.
Add to Basket
$79.95 ea.
|
Stainless Steel Turbo
muffler.
Magnaflow.
$69.95ea Muffler only.
Has not been modified
Add to Basket
Stainless Steel dual
in dual out turbo muffler.
If you want to quiet things
down you can use 1 or 2
of these dual Turbo mufflers
and custom make what
you want.
Muffler only, not modified.
$84.95 Add to Basket
|
Header
parts
02 sensor bung.
Only sold with headers
$8.00
Add to Basket
Adaptor
Free with headers.
Band clamps.
$7.95 ea
Add to Basket
|
Now , If you want our bolt on muffler with
stainless steel connecting tube to the headers.
Then here it is.
|
Driver side.
|
From behind.
|
Passenger side.
|
Header kit will contain, 2 Magnaflow
Stainless Steel mufflers.
Stainless steel connecting tube already welded to the muffler
for
the fit as shown above. I can included the tips if you
need, but there
are different looks and lengths that can be added.
Will also contain 2 band clamps that will tighten up and support
the mufflers. You can add any hanger for the rear support and
have it welded at a muffler shop when you put the tubes on.
The kit is $995.00 Add to Basket
|
Engine shot 1
|
Listen & Watch here.
Wait a minuet to load.
See below.
vvvvvvv
|
Engine
shot 2
|
Video
&
Sound #1
|
Video
&
Sound #2
|
Video &
Sound
#3
|
|
|
|
Bolt Delorean
Performance stock catalytic converter.
Now you can
get performance while better protecting the environment.
Special T in conjunction with Eastern first bolt on performance catalytic
converter for the
Delorean. 2 lb's lighter, all Stainless Steel
construction, Built in
heat shield top and bottom
300 larger hole / inch technology and with the latest in OBD11
compliance.
$239.95 Add
to Basket
#100419ST
Comes
with Gasket 100929, nuts
|
Delorean Tune up kits .
DeLorean
basic tune up kit.
Standard Bosch wires Plugs.
$89.95 Add to Basket
Standard Bosch wires & Platinum
+ 4 Plugs
$109.95 Add to Basket
Basic kit above with custom HP
8mm
silicone wires
$124.95
Add to Basket
|
Bosch Performance
tune up kit.
If you want more performance
using standard 7mm stock wires
and more than the standard tune up
kit, then this is
the one.
$139.95 Add
to basket
Above with 8mm wires
$184.95
Add
to basket
|
Delorean spark plug Wires.
Stock & performance.
|
Custom High
Performance 8mm Silicone
Taylor spark plug
wires.
The best and last wires you will ever have to buy.
Custom made for the
Delorean
8mm Silicone plug wires.
Less resistance for more fire power. Less than 350
ohms per foot.
Thicker insulation for less
bleed out. Includes the
high tension coil wire
Precision wound internally for less to no radio interference.
New boots on
both ends.
Up grade from the stock
7mm wires.
Can handle any HP coil such as
MSD Blaster 45,000 volt or the Pertronix 40,000 volt.
Professional hand made.
Limited life warranty.
Can replace individually if needed. $79.95 set
Add
to basket
See more on Delorean Kit page.
|
Custom made blue 8mm
Taylor
silicone plug wires.
As explained above.
Limited Life Warranty
$79.95
Add
to basket
|
Delorean
custom spark plug wire.
MSD 8.5 MM high performance.
50 ohms per foot for
more transfer
fire power.
Limited life warranty
$99.95
Add to Basket
|
|
Bougicord spark plug wire.
These were the original stock wires .
set added 11/11/03
Set of 7 for the $59.95 #102702
Higher resistance
than the
8mm wires
but lower resistance
than the Bosch.
We sell the complete set of 7 for $59.95
while other are $10.00 more.
Add
to basket
|
Delorean tune up kit
with
Bougicord wires
$99.95 as the kit.
Add
to basket
With platinum +4 plugs.
$129.95
Add
to basket
|
Standard Delorean wires.
Bosch Spark Plug wires
for the Delorean.
$44.95,
Add to Basket
Includes coil wire
|
Delorean OE Bougicord
Spark plug wires.
Set of 7, not 6.
For the Delorean
$59.95 #102702
Add
to basket
Higher resistance than the 8mm but
lower resistance than
the Bosch.
|
|
|
|
Delorean Parts, Ignition coils, Caps,
Rotors and access.
|
Delorean Stainless
steel
HV coil wire.
Hand made with 8mm
silicone low resistance
wire. Performance quality.
Ground wire.
|
Delorean Bosch
distributor cap.
Dist cap $18.95
Add to Basket
|
Distributor rotor
$7.95
Add to Basket
|
Delorean stock
Bosch
ignition
coil.
These are new,
Not old NOS like others.
$59.95
Add
to basket
027 0.7ohm
Add pep to your tired Delorean
with a brand new factory fresh
original coil.
|
Bosch High
Performance coil.
$49.95
Add
to basket
Bosch list is $63.35
25,000 volt with
bracket
#030 1.7ohm
Best used with 1.8 ohm
resistor kit
$29.95
Add
to basket
|
Bosch super ignition
coil.
$29.95
Add
to basket
Bosch list is $40.85
18,000 volt, W/O Bracket
#035 1.7ohm
Best used with 1.8 ohm resistor kit
$29.95
Add
to basket
|
Pertronix
Ignition
coil. 40,000 volt.
Performance coil.
$34.95 Add
to basket
40,000 volt
1.5 ohm coil resistance.
Will work with 7mm but
best used with 8mm wires
Original ballast
resistor set up.
|
MSD Blaster ignition
coil.
45,000 volt.
Performance coil.
$42.95
Add
to basket
45,000 Volts.
.7 ohm coil resistance.
Best used with 8mm
High Performance wires
Coil shot.
|
HP Resistor Kit.
1.8 ohm resistor kit.
$29.95
Add
to basket
Normally used on high performance coils.
Coil shot
|
Oil Products
|
Yes, We have Purflux
Delorean Bosch or Mann oil filter
special.
 
These are the ones that won't hit the oil sending unit
because it's to fat.
Made for the Delorean with the anti drain back valve and the
pressure
release valve.
Also comes with the puffy copper washer for the
oil drain
plug.
6 pack German made Bosch $29.95
Add to Basket
6 pack German made Mann $39.95
Add to Basket
6 Pack of German made Mahle
$39.95 Add to Basket
1ea, single Purflux $14.95ea
Add to Basket
Note the gap when using
the Bosch, Mann or Mahle oil filter and
narrow
80 Lb oil
sending unit. No rubbing the sending unit.
|
Delorean oil pressure
send switch for light.
Factory original.
$11.95
Add to Basket
Delorean oil pan gasket.
Delorean oil pan
gasket.
$19.95
Add to Basket
|
|
Delorean oil pressure
send unit saver.
Save a little and get the
same 80lb correct
reading.
Just a hair larger.
$33.95
Add to Basket
Oil Drain Plug
Magnetic.
# 103815M
With new seal.
Add to Basket
$12.95
Brass oil drain plug
Non
magnetic.
Also can be used
for the
automatic
Trans drain plug
Trans drain plug.
Takes a standard 17mm wrench.
$6.95.
Add to Basket
|
Delorean air filters.
For the extra HP you may be looking for.
No modifications needed. Fits the
original box.
|
Delorean K&N performance
air filter.
More performance from K&N air flow filter.
Filter only . You will feel the difference.
$49.95 Add
to basket
Chemicals only
$14.95 Add
to basket
Package of both
$64.90 Add
to basket
|
Delorean stock air
filter.
Air filter $9.95
Add to Basket
|
Delorean Stainless Steel performance
breather
and cold air
intake.
 
As you may know the original air filters are very restrictive
of air flow which
impedes performance.
If you want to see how much, race
the RPM's up with the accelerator spindle and watch the breather
pull
down, then do it with the new free flow air cleaner and see
the difference.
The colder the air the better the
performance. Your going to add some HP and a quicker
response your foot on
the gas peddle demand.
No cutting or modifications. Just a simple pull off and slip
on.
Includes Blue free flow filter, clamps and hardware
and new intake tube.
$429.95 package
Add to Basket
|
Performance
Stainless Steel
breather only.
$349.95
Add to Basket
|
Performance cold air input
tube
with
K&N performance filter.
$119.90 for the kit.
Add to Basket
|
Performance cold air input
tube only.
$69.95
Add to Basket
|
Heat riser hose of exhaust
manifold.
#105926
$17.95 Add to Basket
Stainless Steel wing.
nut kit $16.95
Add
to Basket
For the air breather.
|
Coolant hose passenger side.
Black wing nuts.
for the air breather.
$12.95 set.
Add to Basket
|
Delorean parts 02 sensors.
02 sensors is an automatic adjustment of
the air to fuel mixture. The closer to 14.5 air to 1.0 fuel will
get the best gas mileage. In perfect conditions they need to be
changed every 30,000 miles. If the car sits, or runs rich,
this will cause the 02 to go bad sooner and will not be able to
sense the air.
So, if your not getting the mileage you think you should
and If your cars idling is seeking, then change the 02 first and
then readjust if needed.
|
Delorean oxygen sensor.
Short wire. Bosch
Same electrical
properties but without
connector. If you
can solder, clip and
crimp
your connector on
to this
wire then you can save here.
$22.95
Add to Basket
02 sensor plug in point.
|
Delorean 02 sensor.
Long wire. US Made.
Our own brand of a US
made 02 sensor for the
Delorean. Has the long
wire and connector..
$21.95
Add to Basket
Oxygen sensor installation
information.
|
Delorean oxygen
sensor.
Bosch long wire.
Sensor with connector.
$37.95
Add to Basket
Replace every 30,000
miles
or sooner.
If your idle is
seeking,
then replace
this unit and
readjust the air flow
meter if needed.
|
Spark plugs and related.
HR6 is considered a ( cold ) stock plug
and will take longer to burn off the contaminants and are
not good for short hops and back and fourth to the
store.
The hotter the plug the faster the burn off as the (
HR8 ).
The Champion plug is also a medium heat range plug.
So chose the plug to your driving habits and they will last
longer.
Learn to read the plug and it will tell you what's
going on in the engine.
|
Here are the charts on how to
read spark
plugs.
They can tell you a lot.
|
Were are now carrying
Champion Spark
Plugs.
For the De Lorean.
Champion copper tip plug
$1.49 ea.
Add to Basket
|
Spark plug cleaner.
Great for getting the old plugs
cleaned up and the engine running and
tuned up before you put in that new set of plugs and
contaminating
them also.
Also good for any other spark plug.
$13.95
Add to Basket
|
Delorean Valve cover gaskets.
Valve cover gaskets.
We got the German ones.
$9.95 / pr.
Add
to basket
Right gasket $4.95
102256 Sq. Ends
Add to basket
Left Gasket $4.95
102249 Rounded end.
Add
to basket
|
Delorean
New stock belts.
Not NOS.
Alternator belt for
Motorola
Alternator.
$9.95
Add to basket
Alternator belt for
Special T alternator.
Dayco $9.95
Add to basket
Stock AC belt
thicker
and larger.
$9.95
Add to basket
Gates A/C Green Stripe
$15.95
Add to basket
|
Delorean vacuum silicone
hoses kit. Warranty life.
Cut to length. Plug and play.
All set are numbered
with
layout as to where
they go.
$49.95 any color.
Blue Add
to basket
Black Add
to basket
Red
Add
to basket
|
Delorean firing order.
Engine firing order and cylinder numbers.
|
Timing marks.
|
Delorean
ignition
distributor spring
set up.
|
My suggestion for proper alignment.
Hand
turn the engine over so on the
Compression stroke, align
the mark on the crank
shaft pulley with the 13
degree
BTDC mark on the marker plate.
Then make
sure the rotor is
aligned with the mark for #1 cylinder
on the ign dist. You may have
to re stab the dist.
If it's aligned as above, you will
have plenty of adjustment
room
on both sides. See timing marks on left.
|
